• Accueil
• colourlock
• Colourlock – in2Detailing

Colourlock – in2Detailing

4.8 (171) · € 33.99 · En Stock

SP80 Green Masking Tape is a high quality low bake masking tape for precision applications and high performance automotive repair and detailing workshops. With a specially formulated natural rubber and resin adhesive to suit modern bodyshop applications, it is produced on the very latest patented coating equipment to the very highest tolerance standards.

In the bodyshop, SP80 Green is recommended for drying cycles of 80 degrees (30 minutes) and is compatible with most common solvent- and water-based paints and lacquers. It is highly conformable, adapting well to most shaped surfaces and providing good adhesion even on irregular surfaces. SP80 Green is hand tearable and won't break on removal. It leaves no adhesive residue on de-masking (hot or cold surfaces) and leaves a clean, sharp paint edge. What's more, adhesive won’t drag on the surface if this tape is caught with a polishing machine. 

SP80 is a distinctive and easily-recognizable green saturated crepe paper. Users can expect consistent unwind force from the start to the finish of each roll.

Benefits:

• Specific formulation allows it to work perfectly, even in overlapping and with masking paper/film applied
• Resistant to thinners
• Heat resistant up to 80 degrees C (30 minutes)
• No adhesive residue after removal from car body, plastics, glass, rubber profiles, etc 
• Water resistant
• Excellent performance with traditional solvent-based and water-based paints
• Its green colour highlights masked areas
• Good adhesion level
• Easy unwinding
• Well adaptable to shaped surfaces
• Removable without breaking
• Hand tearable 
• No lifting or edge curl

Ideal for use by car detailers for masking trims and rubber prior to machine or hand polishing, and automotive bodyshops for car repair applications when the temperature does not exceed 80 degrees.

Colour: Green
Single Roll Supplied

SP80 Green Masking Tape is a high quality low bake masking tape for precision applications and high performance automotive repair and detailing workshops. With a specially formulated natural rubber and resin adhesive to suit modern bodyshop applications, it is produced on the very latest patented coating equipment to the very highest tolerance standards.

In the bodyshop, SP80 Green is recommended for drying cycles of 80 degrees (30 minutes) and is compatible with most common solvent- and water-based paints and lacquers. It is highly conformable, adapting well to most shaped surfaces and providing good adhesion even on irregular surfaces. SP80 Green is hand tearable and won't break on removal. It leaves no adhesive residue on de-masking (hot or cold surfaces) and leaves a clean, sharp paint edge. What's more, adhesive won’t drag on the surface if this tape is caught with a polishing machine. 

SP80 is a distinctive and easily-recognizable green saturated crepe paper. Users can expect consistent unwind force from the start to the finish of each roll.

Benefits:

• Specific formulation allows it to work perfectly, even in overlapping and with masking paper/film applied
• Resistant to thinners
• Heat resistant up to 80 degrees C (30 minutes)
• No adhesive residue after removal from car body, plastics, glass, rubber profiles, etc 
• Water resistant
• Excellent performance with traditional solvent-based and water-based paints
• Its green colour highlights masked areas
• Good adhesion level
• Easy unwinding
• Well adaptable to shaped surfaces
• Removable without breaking
• Hand tearable 
• No lifting or edge curl

Ideal for use by car detailers for masking trims and rubber prior to machine or hand polishing, and automotive bodyshops for car repair applications when the temperature does not exceed 80 degrees.

Colour: Green
Single Roll Supplied

Flex Edge Grip Backing Plate - 3.5 (90mm) Diameter with 5/16 x 24 Thread for Dual Action Polisher

These backing plates were designed for the DIY guy and professional in mind. The flex edges allow the backing plate to be more forgiving while buffing and fit any of our 4 pads (For example Buff and Shine Pads and Chemical Guys Hex Logic Pads).  For use with our Dual Action Polisher DAS 6 Pro 900W.  May fit other machines, please check with the manufaturer.

SCHOLL Concepts Pad Cleaning Brush is a multi-purpose pad cleaning brush consisting of concentrated various length and gradient bristles to optimise the cleaning of machine polishing pads.

• Cleans without damaging the structure of your pads
• Ideal for use with foam, wool & microfibre machine polishing pads
• Work longer before needing to wash the pads
• Aids removal of excess product trapped in the pads fibres
• Keeps pads working in ideal condition
• Easy to use
• Contoured bristles

Flex Edge Grip Backing Plate - 3 (75mm) Diameter with 5/16 x 24 Thread for Dual Action Polisher

These backing plates were designed for the DIY guy and professional in mind. The flex edges allow the backing plate to be more forgiving while buffing and fit any of our 3 pads (for example Liquid Elemens Centriforce and Scholl Concepts Pads).  For use with our Dual Action Polisher DAS 6 Pro 900W.  May fit other machines, please check with the manufaturer.

• APS Pro FVA50 is a high-quality extension made of anodized aluminum for holding the mini polishing cones and other nanopolishing accessories on your FLEX PXE80 mini polishing machine
• Extends the possible uses of the FLEX PXE80 cordless mini polishing machine!
• Attention: APS Pro FVA50 cannot be linked. The FV50, which is also available, is required to extend the distance from the gear head by a further 50mm.
• made of solid, anodized aluminum
• Dimensions:
  • Overall length: 66mm
  • Length without external thread: 50mm
  • Diameter Ø: 14mm
• Scope of delivery: 1x APS Pro FVA50 extension adapter, 1x collet set

• APS Pro FV50 is a universal, high-quality extension made of anodized aluminum - extends the possible uses of your Flex PXE80 cordless mini-polishing machine!
• Attention: the FVA50, which is also available, is required to hold the mini polishing cones and APS nanopolishing tools.
• made of solid, anodized aluminum
• Extends the distance between the polishing plate and the polishing machine by 50mm and more!
• Dimensions:
  • Overall length: approx. 56 mm
  • Length without external thread: 50mm
  • Diameter Ø: 14mm

• APS Pro FP50 is a high quality Ø50mm professional Velcro plate suitable for Flex PXE80 cordless mini polisher.
• Closes the gap between the Ø30mm and Ø75mm backing pad and allows the unlimited use of Ø50mm polishing sponges
• Rotation and eccentric operation possible
• Velcro diameter: Ø48mm
• Total weight: approx. 28 grams

The COLOURLOCK Leather Cleaning Brush is made of durable natural bristles and has a good quality wooden handle. It is a great tool designed to clean soiling effectively and helps to clean and remove stubborn stains on leather car seats.

It can also be used to clean Alcantara and other Textile materials as long as it's used gently.

Pack contents: 1x COLOURLOCK Leather Cleaning Brush.

1 x COLOURLOCK Mild Leather Cleaner, 125 ml
1 x COLOURLOCK Leather Protector, 150 ml
1 x Cleaning Sponge
1 x Cleaning Cloth

Suitable for: Car Leather, Furniture Leather, Bags & Accessories, Leather       
 - Clothing
 - Artificial leather
 - Aniline leather
 - Refined aniline leather
 - Pigmented leather
 - PU leather
 - Pull Up leather
 - Semi-aniline leather
 - Suede and nubuck leather

Firstly, the leather item should be cleaned thoroughly before refresahing the colour or applying care products. Use COLOURLOCK Mild Leather Cleaner against normal degrees of soiling or COLOURLOCK Strong Leather Cleaner in extreme cases (where the leather has been neglected for many years, for example classic cars languishing in garages and barns). Cleaning prior to the treatment prevents dirt sticking to the leather's surface when using colour or care products. Our COLOURLOCK Leather Cleaning Brush effectively removes ingrained dirt.

For surface care, we recommend our COLOURLOCK Leather Protector. It contains aantioxidants, which stops the leather's decay, and its UV filters protect the leather surface from colour fading and will make the leather soft and supple once more.

The kit is usually sufficient to treat a complete car interior or set of furniture multiple times. The Cleaner should only be used on soiled areas, while the Protector should be applied to all surfaces. In the event of extreme soiling, a larger amount of Cleaner might be necessary. But this is very rare.

Application
Always test any products first on a hidden area in case they affect the colour.

COLOURLOCK Leather Cleaner
The Leather Cleaner is provided in a foam dispenser bottle. Foams clean the leather more efficiently than liquid agents, the consumption is considerably smaller, and the leather does not become wet, which could otherwise lead to hardening after drying.

The Leather Cleaner gently cleans the leather. Put some foam on the Cleaning Sponge and apply to the leather. Remove dirty foam residue with a slightly moistened cloth.

COLOURLOCK Leather Protector
Use COLOURLOCK Leather Protector as soon as the leather has dried after cleaning or colour refreshment, ideally on the following day. Apply with a soft cloth and let dry without polishing. One application is sufficient. Strained surfaces (heavy use or in sunlit areas) should be treated every three months. Clean first to avoid dirt or stains.

These products are also suitable for Cool Leather/SRT (SunReflective Technology) Leather!

1 x COLOURLOCK Mild Leather Cleaner, 125 ml
1 x COLOURLOCK Leather Shield, 150 ml
1 x Cleaning Sponge
1 x Cleaning Cloth

Application areas: Car Leather, Furniture Leather
 - Artificial leather
 - Aniline leather
 - Refined aniline leather
 - Pigmented leather
 - PU leather
 - Pull Up leather
 - Semi-aniline leather
 - Suede and nubuck leather

Application:
Soiled leather should be thoroughly cleaned in advance. This prevents dirt sticking to the leather when applying COLOURLOCK Leather Shield. Our COLOURLOCK Leather Cleaning Brush effectively removes ingrained dirt (use circular motion in all directions for better results).

New leather should be treated with our COLOURLOCK Leather Shield within the first three years to protect it against traces of wear and abrasion, as well as discolouration from clothing (dye transfer). The driver's seat (entry bolsters of sports seats and high support cushions) usually begin showing typical signs of wear over the first three years. Leather Shield will prevent this. Treat the driver's seat every three months, the rest of the leather every six to twelve months.

The amount is usually sufficient to treat a complete car interior or a whole set of furniture multiple times. The Cleaner is for soiled areas only, while the Leather Shield should be applied on all surfaces. Where there is extreme soiling, a greater amount of Cleaner might be needed. But this is very rare.

Always test any products first on a hidden area in case they affect the colour.

Leather Cleaner
The Leather Cleaner comes in a foam dispenser bottle. Foams clean the leather more efficiently than liquid agents, the consumption is considerably smaller and the leather does not become wet, which could otherwise lead to hardening after drying.

The Leather Cleaner gently cleans the leather. Apply some foam on the Cleaning Sponge and proceed with cleaning. Remove dirty foam residue with a slightly moistened cloth.

Leather Shield
The COLOURLOCK Leather Shield provides protection for heavily-strained nappa leather surfaces. The Shield prevents rapid wear and discolouration from clothing. Moisten a terry cloth slightly with Leather Shield and treat the strained areas every three months.

These products are also suitable for Cool Leather/SRT (SunReflective Technology) Leather!

New leather should be treated with our COLOURLOCK Leather Shield within the first three years. New leather does not require any special care yet, but rather an efficient protection against traces of wear and abrasion as well as discolouration from clothing (dye transfer). The driver's seat (entry bolsters of sports seats and high support cushions) usually begins showing typical signs of wear over the first three years. This is prevented with the use of the Leather Shield. Treat the driver's seat every three months, the rest of the leather every six to twelve months.

Amount: 150 ml. This is usually sufficient to treat a complete car interior multiple times.


Application area: New pigmented or surface coloured leather in cars, furniture, jackets & handbags. (Not to be used on porous leathers, Suede or Nubuck)

Application:
Always test any products first in a hidden area for changes or colour correctness!

Wet a terry cloth slightly with COLOURLOCK Leather Shield and let dry. Do not buff or polish straight away after application. One application is sufficient. Repeat every three months on strained surfaces. Clean any soiling first! We recommend using the COLOURLOCK Mild/Strong Leather Cleaner.

These products are also suitable for Cool Leather/SRT (SunReflective Technology) Leather.


Pack contents: 1x COLOURLOCK Leather Shield, 150ml.

COLOURLOCK Leather Protector to be used with the Leather Fresh Dye Kits or on its own after COLOURLOCK Leather Cleaning Spirit.

Ideal for:

• Pigmented leather
• Semi-aniline leather

Application:

1. Always test any products first on a hidden area in case they affect the colour!
2. Use COLOURLOCK Leather Protector as soon as the leather has dried after cleaning or colour refreshment, ideally on the following day.
3. Apply with a soft cloth and let dry without polishing. One application is sufficient. Strained surfaces (heavy use or in sunlit areas) should be treated every three months. Clean before use to prevent dirt sticking to the surface.

Pack contents:  1x COLOURLOCK Leather Protector 150ml

Ideal for cleaning leather car and furniture upholstery, bags, suitcases or clothing.

The COLOURLOCK Mild Leather Cleaner is provided in a foaming dispenser bottle. Foams clean the leather more efficiently than liquid agents, the consumption is considerably smaller and the leather does not become wet, which could otherwise become hard after drying.

How to use:

1. Always test any products first on a hidden area in case they affect the colour.
2. Dispense some foam on a sponge or brush. Do not apply to the leather directly!
3. Clean the leather from seam to seam using the foam; repeat several times, if necessary.
4. Remove dirty foam residue with a slightly moistened piece of cloth, then allow to dry.
5. On older leathers, stains might sink into the surface, or perceived dirt might actually be colour damage. Such stains cannot always be removed by cleaning, in which case, use COLOURLOCK Leather Fresh for refreshing the colour.

Suitable for use on:

• Pigmented leather
• PU leather
• Semi-aniline leather

COLOURLOCK Strong Leather Cleaner is also available.

Pack contents: 1x COLOURLOCK Mild Leather Cleaner 200ml (usually sufficient for the cleaning of a whole car interior or set of furniture).

Ideal for cleaning car leather and leather sofas, chairs, bags, suitcases or clothing.

The COLOURLOCK Leather Cleaner comes in a foaming dispenser bottle. Foams clean the leather more efficiently than liquid agents, the consumption is considerably smaller and the leather does not become wet, which could otherwise lead to hardening after drying.

How to use:

1. Always test any products first on a hidden area in case they affect the colour.
2. Dispense some foam onto a sponge or brush. Do not apply to the leather directly!
3. Clean the leather from seam to seam using the foam; repeat several times, if necessary.
4. Remove dirty foam residue with a slightly moistened cloth and allow to dry.
5. On older leathers, stains might sink into the surface, or perceived dirt might actually be colour damage. Such stains cannot always be removed by cleaning, in which case, use COLOURLOCK Leather Fresh for refreshing the colour.

Pack contents:  1x 200 ml Strong Leather Cleaner (usually sufficient for cleaning a whole car interior or set of furniture)

Foam Cannon Pro and Foam Cannon S are new generation Foam Cannons, powered by MJJC’s new generation foam technology. This new technology is stronger and creates more, thicker foam with less soap, even with smaller pressure washers. They have a better connection system. This allows them to attach to your pressure washer easily, and makes changing attachments easier and faster.

Simply put, they are better, stronger, and save you soap, while creating more foam,  making it easier and quicker to foam your vehicle.

Please note regarding connectors.  If you have a short trigger gun, you will need to 1/4 quick release option from the drop down menu.
If you have a Kranzle Pressure washer, please check whether your connector is a D10 or D12 and select accordingly from the drop down menu.
If you have a Nilfisk domestic pressure washer (C/E/P series) you will either need the Gerni/New Nilfisk connector if your pressure washer was purchased within the last 2-3 years.  For older machines, please purchase the Nilfisk/Kew/Alto option.
If you have an AVA Pressure washer, unfortunately this item is NOT compatible with your pressure washer

Features

1. Larger Tank (approximately 1200ml) increases foam production.
2. Anti-leak Tank Cap allows you to foam chassis or roof without leaking.
3. Leak-proof stability is perfect for storing extra or leftover cleaning solution.
4. 360° Degree Adjustable Spray Direction feature makes it easier to foam the roof and chassis of your vehicle.
5. Better foam fan is produced with the new spray nozzle.
6. Thicker foam is produced using less shampoo(soap), which saves you money.
7. Produces 30% denser foam than the first generation foam cannon with the same amount of shampoo.
8. Thick foam can be produced even with 90Bar(1300psi) pressure washers.
9. New connection system (patent pending) makes it easier to attach fittings, no need for PTFE tape or glue.
10. New design makes it easier to change the orifice nozzle and mesh filter.

Description

• Is larger, more stable, and the leakproof tank cap allows you to better foam your vehicle’s chassis and roof, as well as store remaining  liquid without leaking.
• Is designed with the new generation MJJC foam cannon technology, allowing you to rotate the spray nozzle 360° degrees to foam your vehicle’s roof and chassis  easier without wasting foam.
• Produces 30% denser  foam than the classic foam cannon, while  using as little as 100ml of shampoo per 900ml water(1:9 ratio). That means you can create more foam while using less shampoo.
• Produces proper foam even with a 90Bar (1300psi) pressure washer. You won’t need to buy a larger pressure washing machine to produce a dense foam.
• Features the foam fan spray adjuster and top knob, making it easy-to-use!
• Available in a variety of adapters that fit most pressure washers. 
• Comes with a 1.25mm orifice nozzle installed and a 1.1mm orifice nozzle as a spare
• Designed with the new patented Click & Play connection system. Just screw it on, no need for extra PTFE tape or glue to seal your adapters.
• Built with new generation construction, making it stronger and more robust.
• Is newly designed, making it easier to change the orifice nozzle and stainless steel mesh filter.
• This item does not come with a warranty

Först Citrus Pre Cleaner / Pre Wash
The first choice for dirtier jobs.

If your car is really filthy or needs a bit of a spring clean, strip off heavier contamination with Först, our citrus Traffic Film Remover (TFR).

Natural orange oil within the formula doesn’t just boost cleaning – it smells great, as well.

How To Use Citrus Pre Cleaner / Pre Wash?

• Apply it neat to affected areas, leave it for a while to do its thing, then rinse off with your jet wash.
• It’s got more cleaning power than snow foam because there’s no aeration from the foam and it’s sprayed on at full strength using our effective litre spray bottle. Helping your citrus pre wash to be even across the car and not waste the citrus pre cleaner.
• Covering the whole car can waste product, so only spray it on the dirty areas (usually the lower half, and rear, of the car is enough).
• Great value for a litre, because we know you’ll be using this a lot – especially during the winter, enjoy our premium citrus pre wash today.

in2Detailing GEN 2 DA8 Dual Action Machine Polisher **Now Supplied with both 5 (125mm) and 3 (75mm) Backing Plates

Overview: 

Detailing Kingdom Next Cut 1.1 - 500ml/4 Litre
Detailing Kingdom Next Cut 1.1 has been designed from the ground up with the latest compound technology.  Next Cut 1.1 is a water based diminishing abrassive compound utilising a homogenous grain that has been specifically designed to be used on hard and soft clear coats.  It can eliminate deep scratches (P1500) and due to the diminishing abrassives, will also leave a high gloss finish.  To further enhance the finish we recommend following with Next Cut Finale.  
On softer paints where some users can experience 'stickiness' due to heat build up, we recommend spraying the pad with Detailing Kingdom Celebrate which will not only help to reduce the temperature but will also act as a lubricant.

Next Cut 1.1 has been designed to produce little to no dust and polish residue can be removed with absolute ease.  It really is quite a unique compound.

For an exhnaced finish as a one step compound on minor defects, Next Cut 1.1 can be combined with FDT or FDC.  For this, users would add 4 pea size drops of Next Cut 1.1 and 2-3 of FDT or FDC and polish as usual.  The finish will be extremely glossy and protected.

Next cut 1.1 contains no silicone or fillers and is bodyshop safe

Detailing Kingdom Next Cut Finale - 500ml/4 Litre
Detailing Kingdom Next Cut Finale is a water based diminishing abrassive anti-hologram polish.  Next Cut Finale can be used to further exhance the finish after polishing with Next Cut 1.1 or Next Cut 3.3.  Next Cut Finale can also be used to remove light defects such as 5000 grit sanding marks, fine microscratches, and swirl marks. 

Next Cut Finale has been designed to produce little to no dust and polish residue can be removed with absolute ease.

We recommend following Next Cut Finale with Detailing Kingdom FDT or FDC sealant to protect the finish and make it easier to clean.

Next Cut Finale contains no silicone or fillers and is bodyshop safe

Gyeon Q2 AntiFog – in2Detailing

CarPro CQuartz 2.0 Leather Coat – in2Detailing

Stjarnagloss Silke - High Gloss Quick Detailer – in2Detailing

in2Detailing JUMBO Multi Purpose Scrub Pad (2Pk)

Krystal Kleen Detail Purity X – in2Detailing

Forensic Detailing Channel

Stjarnagloss Core Four Kit - Shampoo, Polish, Sealant and

Infinity Wax Synergy Lite Sprayable Ceramic Coating – in2Detailing

in2Detailing Leather & Textile Cleaning Brush for Car Interiors

3D Poxy – in2Detailing

Gyeon Q2M PPF Wash – in2Detailing

Shiny Garage Citrus Oil Pre Wash – in2Detailing

Koch Chemie Malta

303 Salt Neutralizing Wash Boost – in2Detailing

Detailing Kingdom Liquid Sand Matting Compound – in2Detailing